Supply |
|
Voltage
|
12-24 Vdc nom (10 to 30 Vdc) reverse polarity protected, ripple within voltage limits ≤ 5 Vpp.
|
|
Current Consumption
|
60 mA with 20 mA output and transistors energized.
|
|
Power Dissipation
|
1.3 W with 24 V supply, 20 mA output and transistors energized.
|
|
Max. power consumption
|
at 30 V supply voltage, overload condition, transistors output energized and PPC1090 connected, 1.9 W.
|
Input |
|
Type
|
magnetic pick-up, contact, proximity to EN60947-5-6, open-collector transistor for frequency signal up to 50 KHz, TTL CMOS.
|
|
Magnetic pick-up sensitivity
|
≥ 20 mVpp up to 100 Hz input, ≥ 50 mVpp up to 1 KHz, ≥ 100 mVpp up to 5 KHz, ≥ 500 mVpp up to 20 KHz, ≥ 1 Vpp up to 50 KHz.
|
|
Switching current levels
|
ON ≥ 2.1 mA, OFF ≤ 1.2 mA, switch current ≈ 1.65 mA ± 0.2 mA hysteresis (for proximity or transistor input).
|
|
Equivalent source
|
8 V 1 KΩ typical (8 V no load, 8 mA short circuit).
|
|
Integration time
|
100 ms
|
|
Resolution/Visualization
|
1 mHz for 50 Hz range, 10 mHz for 500 Hz range, 100 mHz for 5 KHz range, 1 Hz for 50 KHz range.
|
|
Input range
|
0 to 50.5 KHz maximum.
|
Burnout |
|
Type
|
downscale analog output signal for loss of input signal.
|
Output |
|
Type
|
0/4 to 20 mA, on max. 600 Ω load source mode, current limited at 22 mA or 0/1 to 5 V or 0/2 to 10 V signal, limited at 11 V.
|
|
Resolution
|
1 µA current output or 1 mV voltage output.
|
|
Transfer characteristic
|
linear direct or reverse.
|
|
Response time
|
≤ 50 ms (10 to 90 % step change).
|
|
Output ripple
|
≤ 20 mVrms on 250 Ω load.
|
Repeater Output |
|
Type
|
voltage free SPST optocoupled open-collector transistor.
|
|
Output factor
|
direct 1:1 or divided by 10, 100, 1000, 10000, 100000 or 1000000.
|
|
Open-collector rating
|
100 mA at 35 Vdc (≤ 1.5 V voltage drop).
|
|
Leakage current
|
≤ 50 µA at 35 Vdc
|
|
Frequency response
|
50 KHz maximum
|
Alarm |
|
Trip point range
|
within rated limits of input range (see input for step resolution).
|
|
Delay time
|
0 to 1000 s, 100 ms step.
|
|
Hysteresis
|
0 to 5 Hz for 50 Hz range, 0 to 50 Hz for 500 Hz range,
0 to 500 Hz for 5 KHz range, 0 to 5 KHz for 50 KHz range
(see input visualization parameters for step resolution).
|
|
Output
|
voltage free SPST optocoupled open-collector transistor.
|
|
Open-collector rating
|
100 mA at 35 Vdc (≤ 1.5 V voltage drop).
|
|
Leakage current
|
≤ 50 µA at 35 Vdc.
|
Input performance |
|
Type
|
Ref. Conditions 24 V supply, 250 Ω load, 23 ± 1 °C ambient temperature.
|
|
Calibration and linearity accuracy
|
≤ ± 0.05 % of full scale of selected input range.
|
|
Temperature influence
|
≤ ± 0.005 % of full scale input range for a 1 °C change.
|
Output performance |
|
Type
|
Ref. Conditions 24 V supply, 250 Ω load, 23 ± 1 °C ambient temperature.
|
|
Calibration accuracy
|
≤ ± 0.1 % of full scale
|
|
Linearity error
|
≤ ± 0.05 % of full scale.
|
|
Supply voltage influence
|
≤ ± 0.05 % of full scale for a min to max supply change.
|
|
Load influence
|
≤ ± 0.05 % of full scale for a 0 to 100 % load resistance change.
|
|
Temperature influence
|
≤ ± 0.01 % on zero and span for a 1 °C change.
|
Isolation |
|
Test Voltage
|
I.S. In/Out 1.5 KV; I.S. In/Supply 1.5 KV; Analog Out/Supply 500 V; Analog Out/Digitals Out 500 V; Digital Outs/Supply 500 V; Digital Out/Digitals Out 500 V;
|
Environmental conditions |
|
Operating
|
temperature limits –20 to + 60 °C, relative humidity max 90 % non condensing, up to 35 °C.
|
|
Storage
|
temperature limits – 45 to + 80 °C.
|
Safety description |
|
Safety parameters
|
Uo/Voc = 10.9 V, Io/Isc = 1.1 mA, Po/Po = 3 mW at terminals 13-16.
Uo/Voc = 15.5 V, Io/Isc = 13 mA, Po/Po = 48 mW at terminals 14-15.
Uo/Voc = 10.9 V, Io/Isc = 23 mA, Po/Po = 60 mW at terminals 15-16.
Ui/Vmax = 30 V, Ci = 0 nF, Li = 0 nH at terminals 13-16.
Um = 250 Vrms, -20 °C ≤ Ta ≤ 60°C.
|
Mounting |
|
Type
|
EN/IEC60715 TH 35 DIN-Rail.
|
|
Weight
|
about 155 g.
|
|
Connection
|
by polarized plug-in disconnect screw terminal blocks to accomodate terminations up to 2.5 mm2.
|
|
Location
|
Safe Area/Non Hazardous Locations or Zone 2, Group IIC T4, Class I, Division 2, Groups A, B, C, D Temperature Code T4 and Class I, Zone 2, Group IIC, IIB, IIA T4 installation.
|
|
Protection class
|
IP 20.
|
|
Dimensions
|
Width 22.5 mm, Depth 99 mm, Height 114.5 mm.
|
