TB-D5208-SCH-001 G.M. International S.p.A.
GM International

  • Search
  • RESERVED AREA
    Lost Password
    Not registered yet?
    Sign up

TB-D5208-SCH-001

  1. Products
  2. Termination Boards
  3. SCHNEIDER ELECTRIC
TB-D5208-SCH-001
Termination Board 8 positions for Schneider Modicon Quantum with Digital Output card 140 SDO 953 00S

This Termination Board (TB) provides direct connection between the I/O Card of the system and D5200 Series modules. The Intrinsically Safe protection and signal isolation between Safe and Hazardous Area, is provided by D5200 Series Associated Apparatus. The 24 Vdc Power Supply of the TB is connected to two plug-in terminal blocks, for a redundant power supply. The power supply for modules is given by TB power bus.

FEATURES

  • Digital Output 140SDO95300S Schneider card.
  • 8 positions Terminal Board for up to 8 channels.
  • RS-485 Modbus connection
  • Lower cables installation and maintenance costs.
  • Power supplies fault monitoring.
  • Spare fuse provided
  • Mounting hardware provided for: Wall mounting, M4 thread screw; Wall mounting, M4 self tapping screw; Single Din Rail mounting kit.

Discover D5000


STATUS

 
   ACTIVE
Product lifecycle policy (EN)

CHANNELS

8

Request a free and personalized quotation!

Contact us

Technical Data


Supply
Voltage 24 Vdc nom (20 to 30 Vdc) reverse polarity protected, double terminal blocks for redundant power supply, with OR diodes to mix supply voltages.
Connection by polarized plug-in disconnect screw terminal blocks to accommodate terminations up to 2.5 mm2.
2 LEDs indication green color, one for supply 1 and one for supply 2.
Protection fuse 2 A time lag (spare fuse provided on Termination Board).

Fault detection
1) Preventive - abnormal supply voltage supply 1 or supply 2 is < 18 Vdc (Under Voltage, UV) or > 30 Vdc (Over Voltage, OV).
2) Critical - abnormal supply voltages or cumulative fault both supplies are in under (< 18 Vdc) or over (> 30 Vdc) voltage condition OR cumulative fault indication.
LED fault signaling (for both case 1 and 2) 2 red LEDs (UV and OV of supply 1); 2 red LEDs (UV and OV of supply 2); a cumulative module fault red LED.
Relay fault signaling (one for each case 1 or 2) a voltage free NE SPDT - 1 Form C relay contacts (de-energized in fault condition)
Contact material AgCdO.
Contact rating 2 A 36 Vac 72 VA, 2 A 48 Vdc 80 W (resistive load).
Mechanical / electrical life 30 * 106 / 1 * 105 operation, typical.
Coil status LED indication yellow color, turn on when coil is energized.
Connection by polarized plug-in disconnect screw terminal blocks to accommodate terminations up to 2.5 mm2.

I/O Card Interface
Connection one flat 20 poles male connector (requires female mating connector).

Environmental conditions

Operating temperature limits – 40 to + 70 °C, relative humidity max 90 % non condensing, up to 35 °C.
Storage temperature limits – 45 to + 80 °C.

Mounting
Type Hardware included for mounting on wall and single DIN rail.
Weight about 200 g (excluding modules).
Location Safe Area / Ordinary locations.
Dimensions Width 225 mm, Depth 165 mm, Height 125 mm.

Data Sheet


Datasheet of TB-D5208-SCH-001 ( EN )

Certifications


Type Description Area Number Issued by Issue Date
EMC 5700 and TB EAC EMC Declaration of Conformity ( RU ) Eurasian Community ЕАЭС N RU Д-IT.PA08.B.82359/24 CONTROL 2024-09-26

Declarations of Conformity


EU Declaration Termination Boards TB, TBE, TUE ( EN | IT )
Declaration of Conformity G3 compliance ( EN )

Dimensions