X1-IS-TMP-01-S G.M. International S.p.A.
GM International

  • Search
  • RESERVED AREA
    Lost Password
    Not registered yet?
    Sign up

X1-IS-TMP-01-S

  1. Products
  2. Intrinsically Safe Isolators
  3. Temperature Converter
X1-IS-TMP-01-S
I.S. SIL2 Temperature Converter

The Temperature Converter X1-IS-TMP-01 module accepts a low level dc signal from millivolt, thermocouple or 2/3/4-wire resistance/RTD or transmitting potentiometer sensor, located in Hazardous Area. After linearizing it, the module generates, with isolation, a proportional 0/4-20 mA current to the system AI card, suitable for applications requiring SIL 2 level in safety related systems for high risk industries. Output current signal can be direct or reverse. A fault can be issued in case of input sensor burnout (on any wire) or when configurable thresholds are exceeded. If required, the unit can be re-calibrated through X1 Series Gateway family X1-GW. To ease maintenance operations, field devices can be disconnected through a two-position insertion/extraction mechanism. This product requires a dedicated Termination Board.

FEATURES

  • SIL 2 / SC 3
  • Input from Zone 0 / Division 1
  • Installation in Zone 2 / Division 2
  • Loop disconnection to ease maintenance operations
  • Programmable fault in case of burnout or threshold exceeding
  • mV, TC, 2/3/4-wire resistance/RTD or potentiometer input
  • Inversion/scaling/custom output current
  • Mechanical polarization key to prevent destructive mismatches
  • Fully programmable through Gateway
  • High Accuracy
  • Three port isolation, Input/Output/Supply

STATUS

 
   ACTIVE
Product lifecycle policy (EN)

CHANNELS

1

Request a free and personalized quotation!

Contact us

Technical Data


General
Power Dissipation 0.65 W @ 24 Vdc with 20 mA, 250 Ω output load, typical.

System Supply
Voltage 24 Vdc nom (18 to 28.8 Vdc).
Current Consumption 10 mA, @ 24 Vdc with 20 mA output, typical.

System Out
Type Current 0/4 to 20 mA. The module always sinks current and the Termination Board extends its use to source loops.
Maximum load resistance 600 Ω.
Maximum output voltage 28.8 V.
Minimum output voltage 15 V.
Short circuit current 25.5 mA, typical
Transfer characteristic direct or reverse on all input sensors.

Field In
Type Millivolt, thermocouple, 2/3/4-wire RTD or 3-wire potentiometer. Refer to Instruction Manual for more details.
Response time 1 s.
Input range ±100 mV (TC/mV), 0-5 kΩ (RTD/res), up to 10 kΩ (pot).

Fault
Type Fault can be issued in case of input sensor burnout (on any wire) or when the input measure exceeds programmable thresholds.
Response time 1 s.
Fault signalling common fault & fault mirroring on DCS/PLC AI.

Performance
Ref. Conditions 24 V supply, 250 Ω load, 23 ± 1 °C ambient temperature.
Input accuracy Refer to Instruction Manual for temperature sensor accuracy.
Linearity accuracy: ≤ ±5 μV (mV), ±250 mΩ (res), ±0.05% (pot).
Calibration accuracy: ≤ ±8 μV (mV), ±500 mΩ (res).
Temp. influence (1/°C): ≤ ±2 μV (mV), ±200 mΩ (res), ±0.02% (pot).
Output accuracy Linearity accuracy: ≤ ±10 μA.
Calibration accuracy: ≤ ±10 μA.
Temp. influence (1/°C): ≤ ±1 μA/°C.

Isolation
Test Voltage Field In/System Out 2.5 kV; Field In/System Supply 2.5 kV; System Out/System Supply 500 V.

Environmental conditions

Operating temperature temperature limits –40 to +70 °C.
Storage temperature temperature limits –45 to +80 °C.

Safety description
Equipment Associated apparatus and non-sparking electrical equipment.
Safety parameters Uo = Uo = 7 V, Io = 20 mA, Po = 35 mW at terminals A-B-C-Z.
Ui = 20.2 V, Ci = 3 nF, Li = 0 μH at terminals A-B-C-Z.
Um = 250 Vrms or Vdc, -40 °C ≤ Ta ≤ 70 °C.

Mounting
Type On custom Termination Board.
Weight about 65 g.
Dimensions Width 10 mm, Depth 80 mm, Height 120 mm.

Data Sheet


Datasheet of X1-IS-TMP-01 ( EN )

Instruction Manual


CCC Ex safety instruction manual for X1 series ( EN | CN )
FM Control Drawing of X1-IS-TMP-01 ( EN )
Safety Information of X1-IS-TMP-01-S ( EN )
Instruction Manual X1 Series ( EN )
Instruction Manual of X1-IS-TMP-01 ( EN )

Certifications


Type Description Area Number Issued by Issue Date
ATEX FM ATEX I.S. X1 Series English Certificate ( EN ) Europe FM23ATEX0038X FM 2025-08-13
Ex X1 CCC certificate for China ( EN ) China 2025322310006991 NEPSI 2025-11-12
Ex FM US X1 Series Divisions and Zones English Certificate ( EN ) North America FM23US0073X FM 2025-08-12
Ex FM Canada X1 Series Divisions and Zones English Certificate ( EN ) North America FM23CA0055X FM 2025-08-12
IECEx FM IECEx X1 Series English Certificate ( EN ) International IECEx FMG 23.0018X FM 2025-08-12
UKEx FM UKEx I.S. X1 Series English Certificate ( EN ) United Kingdom FM23UKEX0039X FM 2025-08-14

Declarations of Conformity


EU Declaration of Conformity of X1-IS-TMP-01 ( EN | IT )
UK Declaration of Conformity of X1-IS-TMP-01 ( EN )

Dimensions


Image of X_size

Connections


Drawings


3D_drawing_X1-Cartridge_stp ( EN )