D1052Y G.M. International s.r.l.
GM International

D1052Y
Analog Signal Converter, Duplicator, Adder/Subtractor DIN-Rail

The single and dual channel DIN Rail Analog Signal Converter D1052S and D1052D accepts a voltage or current input from externally powered transmitters, located in Hazardous Area, and converts, with isolation, the signal to drive a Safe Area load. Output signal can be direct or reverse. Duplicator type D1052X provides two independent outputs for the single input. Adder, subtractor, low/high selector type D1052Y provides two independent outputs representing input A, input B, input A plus input B, input A minus input B, low/high selector.

FEATURES

  • SIL2 /SIL3
  • Input from Zone 0 (Zone 20), Division 1, installation in Zone 2, Division 2.
  • High Density, four channels per unit.
  • Voltage input, contact, logic level, common positive or common negative, loop powered or bus powered.
  • Flexible modular multiple output capability.
  • Output short circuit proof and current limited.
  • Three port isolation, Input/Output/Supply.
  • EMC Compatibility to EN61000-6-2, EN61000-6-4.
  • 250 Vrms (Um) max. voltage allowed to the instruments associated with the barrier.

STATUS

 
   SPARE-ONLY
Next: OBSOLETE (2025-12-31)

Product lifecycle policy (EN)

ALTERNATIVE PRODUCT

CHANNELS

2

Request a free and personalized quotation!

Technical Data


Supply

Voltage 12-24 Vdc nom (10 to 30 Vdc) reverse polarity protected, ripple within voltage limits ≤ 5 Vpp.
Current Consumption 2 channels
Power Dissipation 70 mA with 20 mA output typical.
Max. power consumption 1.5 W with 24 V supply voltage and 20 mA output typical.

Input

Type 0/4 to 20 mA (-4 to +24 mA reading) separately powered input, voltage drop ≤ 0.5 V or 0/1 to 5 V or 0/2 to 10 V (-2 to +12 V reading) 1 MΩ impedance.
Integration time 100 ms.
Resolution 1 µA on current input, 1 mV on voltage input.
Visualization 1 µA on current input, 1 mV on voltage inpu
Input range -4 to +24 mA on current input, -2 to +12 V on voltage input.

Burnout

Type enabled or disabled. Analog output can be programmed to detect burnout condition with downscale or highscale forcing.
Range low and high separated trip point value programmable between -5 to +25 mA on current input and -3 to +13 V on voltage input.

Output

Type 0/4 to 20 mA, on max. 600 Ω load source mode, current limited at 22 mA or 0/1 to 5 V or 0/2 to 10 V signal, limited at 11 V.
Resolution 2 µA current output or 1 mV voltage output.
Transfer characteristic linear or reverse.
Response time ≤ 50 ms (10 to 90 % step change).
Output ripple ≤ 20 mVrms on 250 Ω load.

Input performance

Type Ref. Conditions 24 V supply, 250 Ω load, 23 ± 1 °C ambient temperature.
Calibration and linearity accuracy ≤ ± 20 µA on current input or ≤ ± 10 mV on voltage input.
Temperature influence ≤ ± 2 µA, 1 mV of input for a 1 °C change.

Analog output performance

Calibration accuracy ≤ ± 0.1 % of full scale.
Linearity error ≤ ± 0.05 % of full scale.
Supply voltage influence ≤ ± 0.05 % of full scale for a min to max supply change.
Load influence ≤ ± 0.05 % of full scale for a 0 to 100 % load resistance change
Temperature influence ≤ ± 0.01 % on zero and span for a 1 °C change.

Isolation

Test Voltage I.S. In/Out 1.5 KV; I.S. In/Supply 1.5 KV; I.S. In/I.S. In 500 V; Out/Supply 500 V; Out/Out 500 V.

Environmental conditions

Operating temperature limits -20 to + 60 °C, relative humidity max 95 %.
Storage temperature limits -45 to + 80 °C.

Safety description

Safety parameters Uo/Voc = 10.8 V, Io/Isc = 4 mA, Po/Po = 11 mW at terminals 14-15-16, 10-11-12. Ui/Vmax = 30 V, Ci = 4.5 nF, Li = 0 nH at terminals 14-15-16, 10-11-12. Um = 250 Vrms, -20 °C ≤ Ta ≤ 60°C.

Mounting

Type EN/IEC60715 TH 35 DIN-Rail.
Weight at 30 V supply voltage, overload condition and PPC1090 connected, 2.1 W
Connection by polarized plug-in disconnect screw terminal blocks to accomodate terminations up to 2.5 mm2.
Location Safe Area/Non Hazardous Locations or Zone 2, Group IIC T4, Class I, Division 2, Groups A, B, C, D Temperature Code T4 and Class I, Zone 2, Group IIC, IIB, IIA T4 installation.
Protection class IP 20
Dimensions Width 22.5 mm, Depth 99 mm, Height 114.5 mm.

Data Sheet


Datasheet of D1052 ( EN )
D1000 Series Common Specifications and Dimensional Drawing ( EN )

Instruction Manual


Instruction Manual D1052 ( EN )
Instruction Manual D1000 Series ( EN | RU )
Ex safety instruction manual for D1000 series ( EN | IT )
INMETRO safety instruction manual for D1000 series ( PT )
UL Control Drawing D1052 ( EN )

Certifications


Type Description Area Number Issued by Issue Date
ATEX DEKRA ATEX D1000 Series English Certificate ( EN ) Europe DMT 01 ATEX E 042 X DEKRA 2022-04-25
ATEX IMQ Zone 2 Applications D1000 Series Certificate ( EN ) Europe IMQ 09 ATEX 013 X IMQ 2022-05-03
EMC D1000 EAC EMC Declaration of Conformity ( RU ) Eurasian Community ЕАЭС N RU Д-IT.НХ37.В.06311/20 EUROCERT 2020-08-13
Ex EAC Ex Certificate for D1000 Series ( RU ) Eurasian Community ЕАЭС RU С-IT.НА67.В.00113/20 TECHNOPROGRESS 2020-09-04
Ex UL-cUL D1052, D1053, D1072, D1073 Divisions and Zones ( EN ) North America 20130115-E222308E UL 2013-01-15
Ex INMETRO Certificate DNV 13.0108 X for D1000 series ( EN ) Brazil DNV 13.0108 X DNV 2022-12-10
IECEx IMQ IECEx Zone 2 Applications D1000 Series Certificate ( EN ) International IECEx IMQ 13.0011X IMQ 2022-05-03
IECEx DEKRA IECEx for D1000 Series ( EN ) International IECEx BVS 07.0027X DEKRA 2022-05-30
Maritime KR Maritime Certificate D1000 Series ( EN ) International MIL20769-EL001 KR 2022-07-04
Maritime DNV Maritime Certificate TAA00002BM for D1000 Series ( EN ) International TAA00002BM DNV-GL 2024-04-05

Declarations of Conformity


EU Declaration of Conformity D1000 series ( EN | IT )
EU Declaration of Conformity for D1000 series (zone 2) ( EN | IT )
EU Declaration of Conformity for RoHS, ASBESTOS. ( EN )
Declaration of G3 compliance for D1000_PSD1000-PSD1001-PSD1001C-PSD1004-PSD1220-PSD1220-098 SERIES ( EN )

Dimensions


Image of D1052S-D1052D-D1052X-D1052Y_size

Connections


Drawings


2d_drawing_D1000_dwg ( EN )
3d_drawing_D1000_dwg ( EN )
3d_drawing_D1000_stp ( EN )

Software


SWC1090-D1000 Software Configurator for Windows ( EN )
Instruction Manual SWC1090 ( EN )

RELATED PRODUCTS