D1054S G.M. International s.r.l.
GM International

D1054S
SIL 2 Repeater Power Supply and Trip Amplifiers DIN-Rail Model D1054S

The single channel DIN Rail Repeater Power Supply and Trip Amplifier D1054S, provides a fully floating dc supply for energizing conventional 2 wires 4-20 mA transmitters, or separately powered 3, 4 wires 4-20, 0-20 mA transmitters located in Hazardous Area, and repeats the current in floating circuit to drive a Safe Area load. Output signal can be direct or reverse. The circuit allows bi-directional communication signals, for Hart-Smart transmitters. Two independent Alarm Trip Amplifiers are also provided. Each alarm energizes, or de-energizes, an SPST relay for high, low, low-startup or burnout alarm functions. The two alarm relays trip points are settable over the entire input signal range.

FEATURES

  • SIL2/SC2
  • Input from Zone 0 (Zone 20), Division 1, installation in Zone 2, Division 2.
  • 4-20 mA loop or 0/4-20 mA externaly powered Input Signal.
  • 0/4-20 mA, 0/1-5 V, 0/2-10 V Output Signal linear or reverse.
  • Wide Band Smart Communication, HART® compatible.
  • Input and Output short circuit proof.
  • Two independent trip amplifiers.
  • Output for burnout detection.
  • High Accuracy, μP controlled A/D converter.
  • Three port isolation, Input/Output/Supply.
  • EMC Compatibility to EN61000-6-2, EN61000-6-4, EN61326-1
  • Fully programmable operating parameters.
  • 250 Vrms (Um) max. voltage allowed to the instruments associated with the barrier.

STATUS

 
   SPARE-ONLY
Next: OBSOLETE (2025-12-31)

Product lifecycle policy (EN)

ALTERNATIVE PRODUCT

Request a free and personalized quotation!

Technical Data


Supply

Type 12-24 Vdc nom (10 to 30 Vdc) reverse polarity protected, ripple within voltage limits ≤ 5 Vpp
Current Consumption 90 mA with 20 mA input/output and relays energized
Power Dissipation 1.7 W with 24 V supply, 20 mA input/output and relays energized.
Max. power consumption at 30 V supply voltage, input short circuit, overload condition, relays energized and PPC1090 connected, 2.9 W.

Input

Type 0/4 to 20 mA (separately powered input, voltage drop ≤ 1 V) or 4 to 20 mA (2 wire Tx current limited at ≈ 25 mA).
Integration time 100 ms
Resolution 1 µA.
Input range 0 to +22 mA

Transmitter line voltage

Type ≥ 15.0 V at 20 mA with max. 20 mVrms ripple on 0.5 to 40 KHz frequency band.

Burnout

Type enabled or disabled. Analog output can be programmed to detect burnout condition with downscale or highscale forcing. Alarms can be programmed to detect burnout condition.
Range low and high separated trip point value programmable between -5 to +25 mA.

Output

Type 0/4 to 20 mA, on max. 600 Ω load source mode, current limited at 22 mA or 0/1 to 5 V or 0/2 to 10 V signal, limited at 11 V.
Resolution 1 µA current output or 1 mV voltage output.
Transfer characteristic linear or reverse.
Response time ≤ 50 ms (10 to 90 % step change).
Output ripple ≤ 20 mVrms on 250 Ω communication load on 0.5 to 40 KHz band.
Frequency response 0.5 to 40 KHz bidirectional within 3 dB (HART® and higher frequency protocols) only with mA direct current output.

Alarm

Trip point range within rated limits of input sensor (see input for step resolution).
ON-OFF delay time 0 to 1000 s, 100 ms step, separate setting.
Hysteresis 0 to 5 mA (see input for step resolution).
Output voltage free SPST relay contact.
Contact rating 2 A 250 Vac 500 VA, 2 A 250 Vdc 80 W (resistive load).

Performance

Type Ref. Conditions 24 V supply, 250 Ω load, 23 ± 1 °C ambient temperature.
Input Calibration and linearity accuracy: ≤ ± 20 μA Temperature influence: ≤ ± 1 μA of input for a 1 °C change.
Analog Output Calibration accuracy: ≤ ± 0.1 % of full scale. Output Linearity error: ≤ ± 0.05 % of full scale. Supply voltage influence: ≤ ± 0.05% of full scale for min to max supply change Load influence: ≤ ± 0.05% of full scale for 0 to 100 % load resistance change Temperature influence: ≤ ± 0.01 % on zero and span for a 1 °C change.

Isolation

Test Voltage I.S. In/Outs 1.5 KV; I.S. In/Supply 1.5 KV; Analog Out/Supply 500 V; Analog Out/Alarm Outs 1.5 KV; Alarm Outs/Supply 1.5 KV; Alarm Out/Alarm Out 1.5 KV.

Environmental conditions

Operating temperature limits -20 to + 60 °C, relative humidity max 95 %.
Storage temperature limits – 45 to + 80 °C.

Safety description

Safety parameters Uo/Voc = 26.3 V, Io/Isc = 91 mA, Po/Po = 597 mW at terminals 14-15. Uo/Voc = 1.1 V, Io/Isc = 56 mA, Po/Po = 16 mW at terminals 15-16. Ui/Vmax = 30 V, Ii/Imax = 128 mA, Ci = 1.05 nF, Li = 0 nH at terminals 15-16. Um = 250 Vrms, -20 °C ≤ Ta ≤ 60°C.

Mounting

Type EN/IEC60715 TH 35 DIN-Rail.
Weight about 175 g.
Connection by polarized plug-in disconnect screw terminal blocks to accomodate terminations up to 2.5 mm2.
Location Safe Area/Non Hazardous Locations or Zone 2, Group IIC T4, Class I, Division 2, Groups A, B, C, D Temperature Code T4 and Class I, Zone 2, Group IIC, IIB, IIA T4 installation.
Protection class IP 20.
Dimensions Width 22.5 mm, Depth 99 mm, Height 114.5 mm.

Data Sheet


Datasheet of D1054 ( EN )
D1000 Series Common Specifications and Dimensional Drawing ( EN )

Instruction Manual


Instruction Manual D1054 ( EN )
Instruction Manual D1000 Series ( EN | RU )
Ex safety instruction manual for D1000 series ( EN | IT )
INMETRO safety instruction manual for D1000 series ( PT )
UL Control Drawing D1054 ( EN )

Certifications


Type Description Area Number Issued by Issue Date
ATEX IMQ Zone 2 Applications D1000 Series Certificate ( EN ) Europe IMQ 09 ATEX 013 X IMQ 2022-05-03
ATEX Presafe ATEX for D1054, D1061, D1063 ( EN ) Europe Presafe 16ATEX8917 PRESAFE 2017-05-22
EMC D1000 EAC EMC Declaration of Conformity ( RU ) Eurasian Community ЕАЭС N RU Д-IT.НХ37.В.06311/20 EUROCERT 2020-08-13
Ex EAC Ex Certificate for D1000 Series ( RU ) Eurasian Community ЕАЭС RU С-IT.НА67.В.00113/20 TECHNOPROGRESS 2020-09-04
Ex FM No.3024643-3029921C Certificate ( EN ) North America 3024643-3029921C FM 2005-12-16
Ex INMETRO Certificate DNV 13.0135 X for D1054, D1061, D1063 ( EN ) Brazil DNV 22.0245 Rev. 0 DNV-GL 2022-12-10
FSM TUV IT 22 SIL 0093 Functional Safety Certificate ( EN ) International TUV IT 22 SIL 0093 TUV_SUD 2022-07-25
IECEx IMQ IECEx Zone 2 Applications D1000 Series Certificate ( EN ) International IECEx IMQ 13.0011X IMQ 2022-05-03
IECEx Presafe IECEx for D1054, D1061, D1063 ( EN ) International IECEx PRE 16.0084 PRESAFE 2017-05-22
Maritime KR Maritime Certificate D1000 Series ( EN ) International MIL20769-EL001 KR 2022-07-04
Maritime DNV Maritime Certificate TAA00002BM for D1000 Series ( EN ) International TAA00002BM DNV-GL 2024-04-05
Metrological Metrological Certificate Russia for D1000 Series ( RU ) Russia 64283-11 ROSSTANDART 2021-03-10
SIL TUV C-IS-722238330 SIL Declaration of Compliance Summary ( EN ) International C-IS-722238330 TUV_SUD 2024-01-19

Declarations of Conformity


EU Declaration of Conformity for D1000 series (zone 2) ( EN | IT )
EU Declaration of Conformity for D1054, D1061, D1063 ( EN | IT )
EU Declaration of Conformity for RoHS, ASBESTOS. ( EN )
Declaration of G3 compliance for D1000_PSD1000-PSD1001-PSD1001C-PSD1004-PSD1220-PSD1220-098 SERIES ( EN )

Dimensions


Image of D1054S_size

Connections


Drawings


2d_drawing_D1000_dwg ( EN )
3d_drawing_D1000_dwg ( EN )
3d_drawing_D1000_stp ( EN )

Software


SWC1090-D1000 Software Configurator for Windows ( EN )
Instruction Manual SWC1090 ( EN )